Water Testing in Cape Town with SANS Water. We test ground water and council water with a SANAS accredited laboratory

Maintaining a Filtration System: 10 Simple Steps for Clean Water

A filtration system only works if you look after it. However, many owners forget it until something changes. Then pressure drops, taste suffers and the pump strains. This guide gives you ten simple steps for maintaining a filtration system. Follow them, and your household filtration will run well for years.

Why Maintaining a Filtration System Matters

Using ground water in the house is common in Cape Town. Borehole water often carries sediment, iron and bacteria. Therefore, your filters work hard every day. Over time, they clog and stop doing their job. As a result, water quality drops and pumps work harder. Regular care prevents this.

Before You Start

Gather a few basics first. You need white cotton gloves, a bucket, a housing spanner and spare filters. Also, keep your manufacturer’s manual close. Models differ, so check their advice too.

10 Steps for Maintaining a Filtration System

Step 1: Turn Off the Power

First, always start here. Switch off the pump and the UV unit at the mains. This keeps you safe and protects the equipment.

Step 2: Close the Taps and Release the Pressure

First, close all the taps on the system. Then run a household tap to take the pressure out of the system and canisters. This makes the canisters easier to remove. It also stops you getting wet.

Step 3: Remove and Inspect Every Filter

Next, take out all the filters. Then look for discolouration. On your activated carbon block, check for slime or staining around the washers. Either sign means it needs replacing.

Replace sediment filters at least every 6 months. They may look white but still be clogged. Moreover, clogged filters strain the pump and drop your water pressure.

Step 4: Check the UV Bulb

Listen for beeping, or look for flashing lights. Both mean the bulb has failed. Most UV bulbs need replacing about once a year, even if they still glow.

To swap the bulb, make sure the power is off. Next, put on white cotton gloves. Disconnect the bulb and slide it out. Then slide in the new bulb and reattach it. Never look at a lit UV bulb.

Step 5: Backwash and Rinse a Manual System

Set the backwash head to backwash. Reopen all the taps, then turn the pump on. Backwash for 3 to 5 minutes, or until the water runs clear. Next, turn the pump off and move the head to rinse.

Turn the pump back on and rinse for 3 to 5 minutes. Finally, switch the pump off again.

Step 6: Clean the Housings and Check the O-Rings

While the canisters are empty, wash them with clean water. Also check each rubber O-ring for cracks. A light smear of silicone grease helps it seal. Use silicone only, because other greases can damage the rubber.

Step 7: Refit the Filters and Restart Safely

Next, fit the new filters in the correct order. Then hand-tighten the canisters. Open the taps slowly and switch the pump on. Let the trapped air bleed out. Finally, check every joint for leaks.

Step 8: Look After Your Reverse Osmosis and Activated Carbon Stages

Reverse osmosis (RO) systems need extra care. Replace the pre-filters and activated carbon stages on schedule. Otherwise, they can damage the RO membrane. Most RO membranes last two to three years, but check your manual.

Also, watch for slow flow or a change in taste. These are early warnings that a stage needs attention.

Step 9: Check Iron Removal Systems and Test the pH

If you have iron removal systems, make sure they backwash or regenerate as designed. Rust-coloured water and orange stains signal trouble.

Next, ask yourself, is my water acidic? Acidic water can corrode pipes and fittings. It can also leave blue-green stains. A simple pH test gives you the answer. If the pH is low, a neutralising filter may help.

Step 10: Test Your Water and Keep a Service Log

Finally, test your water at least once a year. SANS 241 water testing shows whether it meets drinking standards. Then record each filter change and pressure reading in a log. That way, you always know what is due next.

How Often Should You Service a Filtration System?

So, use this guide as a starting point. However, your manual and water quality may change the timing.

  • Sediment filters. At least every 6 months.
  • Activated carbon. Every 6 to 12 months, or sooner if you see slime or staining.
  • UV bulb. About once a year.
  • RO membrane. Every two to three years.
  • Water test. At least once a year.

Where Can I Buy New Filters?

Many owners ask, where can I buy new filters? Buy from a specialist who matches filters to your system. The wrong size or micron rating causes leaks and poor results. Therefore, speak to SANS Water for advice on the right filters for your setup.

Where Can I Find Someone to Maintain My Filtration System?

Prefer not to do it yourself? Then book a professional service. One visit can cover flow, pressure, UV output and water quality. Moreover, a technician spots small faults before they become costly. Ask for a written report each time.

The Bottom Line

Maintaining a filtration system takes little time. However, skipping it costs far more in repairs and poor water. So, schedule your next service today.

Talk to Mike at SANS Water

Need filters, a service or a water test? Speak to Mike at SANS Water for advice you can trust.

Visit www.sanswater.co.za or WhatsApp 084 400 4300.

 

© 2026 SANS Water | All rights reserved | Terms and Conditions | Design and development by Michael Hastie.

Water Testing in Cape Town with SANS Water. We test ground water and council water with a SANAS accredited laboratory

Site created and maintained by www.mikehastiemedia.com

+27 (0) 21 788 1302 | mike@sanswater.co.za
50 Promenade Road, Lakeside, Cape Town, South Africa